GIZA MEDITATION PYRAMID CONNECTOR KIT for 1/2" Type M Copper pipe

Description

GIZA Pyramid Connector Kit
For Type M Copper Pipe
Offered is one 5 piece set of semi-flexible 1/2" plastic connectors and apex for constructing a 51° angle GIZA pyramid using Type M Copper pipe. (No pipe is provided with this listing)
The picture showing three different base fittings is for angular reference and visualizing the differences with each angle. The pictures provided of assembled pyramids are for pictorial demonstration only - no pipe, constructed pyramid or additional fittings beyond the stated connector quantity above are being supplied.
Save money by buying your own Type M Copper pipe from a hardware store such as Home Depot. Some fit adjustment may be necessary to the pipe if using other vendor supplied or type pipe. It is suggested to take a base fitting to the store and test the fit on a store cut smooth pipe end before purchasing the pipe.
Depending on the size of the pyramid you want to construct (any size pyramid may be constructed) the lateral edge that starts from the base tip to the apex/cap tip is calculated using a Phi ratio of 1.272 multiplied by one base side length.
For example and shown in the provided pictures, if your desired base is 12" square you would multiply 12" X 1.272 = 15.264" Inches – (round this number to 15 1/4” for ease of measurement)
From this calculation you would need 4 pieces of ½” Type M Copper pipe 15 ¼” long and 4 pieces of ½” Type M Copper 12" long.
However, before you run out and start cutting pipe to size there are an additional set of steps required when using these particular fittings to obtain an accurately sized pyramid structure. These are as follows:
1. Take each base length (12”) of pipe and subtract
3 1/2” from each of the 12” base pieces then cut to this length.
This will provide four base pieces with an actual finished length of 8 1/2” each.
2. Take each calculated lateral piece (15 1/4”) and subtract 5 1/2”
from each of the pieces then cut to this length.
This will provide four lateral pieces with an actual finished length of 9 3/4” each.
The adjustments of the pipe lengths detailed in the example above allow for an exact and very accurate pyramid construction that accounts for the added material of the base fittings and the apex piece. This will center the calculated geometric lines of the pyramid to the construction material center line(s) forming a 12" square base.
The fittings for this pyramid are a press/slip fit for assembly and are very stable. This design eliminates set screws to tighten the pipe to the fittings and will allow for easy dismantling your pyramid for movement when desired. If a permanent structure is desired, one may use epoxy adhesive or similar glue to fix the pieces permanently in place.
Please note: These fittings do not provide for pipe interconnection to one another for a full conductive circuit.
In addition to the above, there are several added design features that are provided within this set of fittings that are not available on other connector sets:
An ability to place legs or extensions into the bottom of each base fitting which will allow the user to elevate the pyramid to a chosen height while still maintaining the pyramid angles and center lines.
(No pipe or extra fittings for this purpose are provided within this offering)
Alternatively, added extensions can be placed into the ground to anchor the pyramid against wind or other disturbances that may move it around when used outdoors.
The base fittings may be used as cross member support extensions for any pyramid size that requires cross support structure due to its' size and to help eliminate possible pipe sagging on extremely long lateral lengths.
(Additional set(s) of fittings will need to be purchased separately for this function)
The apex has a removeable capstone with a hidden chamber within to place any object within such as a crystal, shungite, miniature tensor ring, or anything else that fits and will suit your need.
Basic construction instructions will be provided with each kit
Should you require more pyramid connector sets than are currently listed for sale, please make contact to arrange for the quantity you need.
If you would like to be able to purchase individual components such as only the Apex - please ask. I can provide whatever parts you need for a nominal cost with free shipping.
All pyramid parts supplied are proudly manufactured in the USA.